How to Use an EverStart Maxx Jump Starter (Lead-Acid and Lithium)
To use an EverStart Maxx jump starter, check the charge display, turn the car off, clamp red to the battery positive and black to an engine ground, then turn the jump power on and crank for up to 5 seconds. Turn it off, remove black then red, and recharge the unit fully before storing it.
EverStart Maxx is Walmart’s premium battery and jump starter line. You will see two main kinds on the shelf: lead-acid jump boxes with an air compressor (such as the 1200 peak amp model many people buy) and compact lithium packs that charge over USB. The store brand has been built by different manufacturers over the years, so control layouts vary.
The safe sequence does not change. This guide walks through it, then covers what to expect from each type and how to keep the unit ready.

EverStart Maxx Lead-Acid vs Lithium
| Point | Lead-acid jump box | Lithium pack |
|---|---|---|
| Weight | Heavy, often 15 to 20 lb | Light, 1 to 3 lb |
| Extras | Air compressor, USB, 12V socket, work light | USB ports, flashlight |
| Charging | AC cord or adapter, sometimes 12V cord | USB-C or micro-USB |
| Holds charge | Needs monthly top-up | Holds charge for months |
| Best for | Home garage, trucks, tire inflation | Glove box, everyday carry |
Both types work the same at the clamps. The lead-acid units deliver strong current for longer cranks, while lithium packs are easier to keep with you.
Before You Jump
- Read the display or press the battery status button. Many EverStart Maxx boxes show charge as LEDs or a percentage. If it is low, charge it first. A low unit will click the starter and give up.
- Turn the vehicle off, pull the key, and switch off headlights, wipers, blower and radio.
- Wear safety glasses and look at the car battery. Do not jump a battery that is cracked, swollen, leaking or frozen.
- Find the right terminals. Some cars hide the battery in the trunk or under a seat and provide jump posts under the hood.
Battery terminal cleaning brush
Corroded terminals are the most common reason a good jump starter fails; a two-way post and clamp brush clears the contact surface in seconds.
As an Amazon Associate, ReplaceKeyFob earns from qualifying purchases.
How to Use an EverStart Maxx Jump Starter
- Make sure the jump power is off. On units with a jump or power switch, set it to off before clamping.
- Attach the red clamp to the positive (+) terminal.
- Attach the black clamp to a bare metal ground on the engine block or chassis, away from the battery and fuel lines.
- Watch for warnings. If a reverse-polarity light comes on or an alarm sounds, disconnect and reconnect correctly.
- Turn the jump power on. Some lithium models activate automatically when they detect a correct connection.
- Crank for up to 5 seconds.
- Wait 1 to 2 minutes between tries. It lets the starter cool and gives the unit time to recover.
- When the engine starts, turn the power off before removing clamps.
- Remove the black clamp, then the red one.
- Drive 20 to 30 minutes to recharge the car battery.

Using the EverStart Maxx 1200A Jump Starter
The 1200A peak rating suits most cars, SUVs and many V8 trucks. A few tips get better results from it:
- Pre-charge a very flat battery. If the car battery is extremely low, connect the unit, turn the power on, and wait a minute or two before cranking (if your manual allows it). This gives the car battery a small boost before the big starter load.
- Clamp the engine block on trucks. A short ground path helps on V8s.
- Diesels need patience. Cycle the glow plug light before cranking. See our guide on how to jump start a truck.
Using an EverStart Maxx Lithium Jump Starter
Lithium models are simpler and usually have built-in safety logic:
- Connect the clamp module (often a box on the cable) to the pack.
- Clamp red to positive and black to ground.
- Wait for a green ready light on the clamp module or pack.
- Crank. If the battery is too low to detect, some models have a boost or override button; use it only if you are certain the clamps are correct.
For general lithium pack technique, see how to use a jump starter.
Reading the EverStart Maxx Manual
If you lost the paper manual, the model number is printed on a label on the back or bottom of the unit. Search that model number with the word “manual” to find a PDF, or check the product page where you bought it. Look for three things in it: how long to charge before first use, whether the unit can stay plugged in, and the duty cycle for the compressor.
How to Use the Air Compressor
- Start the vehicle if you can, to save the unit’s battery.
- Connect the hose chuck to the tire valve.
- Set the target pressure if your model has auto-stop. Use the PSI on the driver door jamb.
- Turn the compressor on and let it run in short cycles.
- Check the pressure with a separate gauge when done.
How to Charge an EverStart Maxx
- Lead-acid boxes: charge through the AC cord or adapter (or a household extension cord on models with a built-in charger). Charge fully before first use. Recharge after each use and every month in storage.
- Lithium packs: charge over USB with the included cable and a wall adapter. Recharge after each use and every 3 months.
Never store a lead-acid unit flat. It can lose capacity permanently in a few weeks. Our guide on how to charge a jump starter covers charge times and storage.
Troubleshooting an EverStart Maxx
| Symptom | Likely cause | Fix |
|---|---|---|
| No power at clamps | Switch off, low charge, blown internal fuse | Turn power on; charge; check manual for fuse |
| Polarity light or beep | Clamps reversed | Swap clamps |
| Clicking, no crank | Weak contact at clamps | Clean terminals, ground to engine block |
| Cranks slow | Unit low or undersized | Charge; pre-charge battery 1 to 2 minutes |
| Unit dies fast after full charge | Worn internal battery | Replace battery or unit |
| Car starts, battery dead next day | Bad car battery or drain | Test the battery |
A car battery that needs a jump more than once needs testing, not more jumps. See how to test a car battery with a multimeter.
Where to Clamp on Cars With Hidden Batteries
Many newer cars put the battery somewhere the short cables on a jump box cannot reach. In those cases the car has jump posts under the hood, and you should use them:
| Battery location | Common on | Where to clamp |
|---|---|---|
| Trunk or under the trunk floor | Many BMW, Mercedes, Audi, some Chrysler and Dodge sedans | Positive post under the hood (red cap) and the marked ground stud |
| Under the rear seat | Some GM SUVs and Cadillacs | Under-hood positive post and engine ground |
| Under a cowl panel or behind a liner | Some newer crossovers | Under-hood jump terminal if fitted |
| Hybrid 12V in the cargo area | Many Toyota hybrids | Jump terminal in the under-hood fuse box |
If you cannot find the post, the owner’s manual index lists it under “jump starting.” For hybrids, see how to jump start a hybrid car.
Safety Tips
- Store clamps in their holders so they cannot touch.
- Keep the unit off the engine while jumping.
- Do not use the AC outlet or compressor while cranking.
- Charge in a ventilated area, away from sparks.
- If the case smells of acid, bulges or leaks, stop using it and recycle it at a store that takes lead-acid batteries.
Returns, Warranty and Cost
EverStart Maxx products are sold at Walmart with a limited warranty, so keep your receipt. Lead-acid jump boxes with compressors are typically about $90 to $170 in 2026, and lithium packs about $60 to $150. If the internal battery has failed after the warranty, a new unit is often more practical than a repair. Our list of portable jump starters has other options if you are replacing it.
Frequently Asked Questions
Charge it, clamp red to positive and black to engine ground, turn the jump power on, and crank for up to 5 seconds. On a very flat battery, some models let you wait a minute or two with power on before cranking.
Lead-acid models charge with an AC cord or adapter, and some use a household extension cord into a built-in charger. Lithium models charge over USB. Charge fully before first use and after every jump.
Check that it is charged, the power switch is on, and the clamps have clean metal contact. If a polarity light is on, the clamps are reversed. If it dies quickly after a full charge, the internal battery is worn.
Find the model number on the label on the unit, then search that number with “manual” or check the retailer’s product page, which often links a PDF.
Yes, if its rating suits the engine size. Large V8 and diesel engines need a higher-rated pack, especially in cold weather.
